For Android phones with a built-in infrared blaster
Point your phone at the air conditioner and press the button. No pairing, no account, no Wi-Fi.
One screen, big buttons, the room temperature where you expect it.
The button you actually need. Send power on or power off from the lock screen widget without opening anything else.
Step the setpoint up or down and move the fan between low, medium, high and auto, the same codes the plastic remote sends.
Switch modes directly instead of cycling through them blind. Which modes appear depends on what your unit accepts.
Shut the unit off an hour after you fall asleep, or have it start before you get home. The phone sends the command when the time comes.
A library of infrared code sets covering the common wall-mounted split units. You pick the brand, test the power code, and keep the set that answers.
Store the combinations you use — 24° quiet for the bedroom, 20° strong for the living room — and send one in a tap.
This is the one question that decides everything, so it goes first rather than last. CONDITIONER KOP does not talk to your air conditioner over Wi-Fi, Bluetooth or the internet. It uses the same thing the plastic remote uses: a small infrared emitter that flashes a pattern of invisible light at the unit. Some Android phones have one, usually as a tiny dark window on the top edge beside the microphone. Many phones do not. If yours does not, no app of this kind will work on it, ours included, and we would rather you read that here than discover it after installing.
Look at the top edge of the phone for a small black or dark red window. Then open your phone's settings and search for infrared or IR blaster; on phones that have one, a remote-control feature usually appears in the results. If you are still unsure, search your exact model name together with the words "IR blaster" — or send us the model on this page and we will tell you yes or no.
Infrared is line of sight. The signal travels like torchlight: it bounces off a white ceiling well enough, but it does not go through a wall, around a corner or out of the room. So the phone has to be in the same room as the unit, pointed roughly at it, within the distance the original remote worked at. In exchange you get something the connected products cannot offer — it works with the router down, with mobile data off, in a rented flat, on a unit that was installed long before anything had an app. There is no account to make and nothing to pair.
There is no single standard for air conditioner infrared codes. Each manufacturer, and often each generation of unit, uses its own packet format, and a remote that looks identical on two brands can be sending something completely different. That is why the setup asks for your brand and then has you test: you send a power command, and if the unit beeps, that code set is yours. If it does not, you try the next one in the list. It is a few seconds of trial rather than magic, and it is the honest way to cover a lot of hardware with one app.
It does not read the temperature of your room — the number on the screen is the setpoint you are sending, not a sensor reading. It cannot report back what state the unit is in, because infrared only goes one way; if someone else used the plastic remote, the app does not know. It will not control a unit that only accepts commands from its own cloud app, and it will not make an old unit do something it was never built to do. Everything else — power, temperature, fan, mode, timer — is exactly the set of buttons that were on the remote you lost.
Check that the phone has an infrared blaster. If you are not sure, send us the model and we will check it for you.
Choose your air conditioner's manufacturer from the list to narrow down which infrared code sets to try.
Aim at the indoor unit and send power. A beep or a change on the display means you found the right set — if nothing happens, step to the next one.
Store the settings for each room, add a timer if you want the unit off at night, and put the on/off control where you can reach it quickly.
No. Without an infrared emitter the phone has no way to send the signal, and no software can add one. If your air conditioner has its own Wi-Fi module, the manufacturer's own app is the route for you.
Neither. The command goes straight from the phone's infrared emitter to the unit. It works with mobile data off and with the router unplugged.
No. Infrared needs line of sight, the same as the original remote. Same room, pointed roughly at the indoor unit, and it will reach.
The common wall-mounted split units from the widely sold manufacturers, through a library of infrared code sets. Because formats differ between models, you confirm yours by testing the power command during setup.
Yes. The unit does not care who sent the command, so the app and the remote can be used side by side. The app just will not know what the remote did.
That number is the setpoint being sent, not a measurement. The phone cannot read the room, and infrared gives no reply from the unit.
Send the model name and we will tell you plainly whether that phone can run an infrared remote — and anything else you want to ask about the app.
Thank you — someone from the team will get back to you shortly with an answer about your phone.
This site uses cookies for analytics and advertising measurement only after you give your consent. Learn more